Flow Inducer Sleeves & When To Use Them
By: Juan IbarraFlow Inducer Sleeves & When To Use Them
Good day! I’m Juan, and welcome to my TED Talk on flow sleeves. Today, I’ll explain how a flow sleeve helps cool a submersible well motor and when your installation may need one.
Submersible well motors rely on water moving past them to carry away heat as they run. In some installations, water can reach the pump intake without flowing past the motor. A flow sleeve directs that water along the motor first, helping keep it cool and prevent overheating.
There are some cases that require a flow sleeve to help cool the motor during operation some examples are as follows:
1. When the well diameter is too large to meet flow requirements.
2. When the pump is in an open body of water or cistern tank.
3. If the pump is in a rock well or below the well casing.
4. If the well is top-feeding or cascading.
5. Lastly if the pump is set in or below screens or perforations.
These are some instances when you will want to use a flow sleeve to ensure that water is flowing past the motor to keep it cool.
Minimum Flow Required for Motor Cooling
|
Casing / Sleeve ID Inches (mm) |
4" Motor (3-10 HP) @ 0.25 ft/s flow GPM (L/M) |
6" Motor @ 0.50 ft/s flow GPM (L/M) |
8" Motor @ 0.50 ft/s flow GPM (L/M) |
|
4" (102 mm) |
1.2 (4.5) |
— |
— |
|
5" (127 mm) |
7.0 (26.5) |
— |
— |
|
6" (152 mm) |
13.0 (49.0) |
9.0 (34.0) |
— |
|
7" (178 mm) |
20.0 (76.0) |
25.0 (95.0) |
— |
|
8" (203 mm) |
30.0 (114.0) |
45.0 (170.0) |
10.0 (40.0) |
|
10" (254 mm) |
50.0 (189.0) |
90.0 (340.0) |
55.0 (210.0) |
|
12" (305 mm) |
80.0 (303.0) |
140.0 (530.0) |
110.0 (420.0) |
|
14" (356 mm) |
110.0 (416.0) |
200.0 (760.0) |
170.0 (645.0) |
|
16" (406 mm) |
150.0 (568.0) |
280.0 (1060.0) |
245.0 (930.0) |
When a standard water well motor is operated in water over 86 degrees fahrenheit the water flow past the motor needs to be increased in order to maintain safe motor operating conditions.
Table: Minimum GPM Required for Motor Cooling in Water Up to 194 °F (3 ft/s Velocity)
|
Casing or Sleeve I.D. |
4" High Thrust Motor |
6" Motor |
8" Motor |
|
4 inches (102 mm) |
15 GPM (57 L/m) |
— |
— |
|
5 inches (127 mm) |
80 GPM (303 L/m) |
— |
— |
|
6 inches (152 mm) |
160 GPM (606 L/m) |
52 GPM (197 L/m) |
— |
|
7 inches (178 mm) |
— |
150 GPM (568 L/m) |
— |
|
8 inches (203 mm) |
— |
260 GPM (984 L/m) |
60 GPM (227 L/m) |
|
10 inches (254 mm) |
— |
520 GPM (1970 L/m) |
330 GPM (1250 L/m) |
|
12 inches (305 mm) |
— |
— |
650 GPM (2460 L/m) |
|
14 inches (356 mm) |
— |
— |
1020 GPM (3860 L/m) |
|
16 inches (406 mm) |
— |
— |
1460 GPM (5530 L/m) |
There are manufacturers such as Franklin Electric that do offer Hi-Temp submersible motors. These motors are designed to operate in water with higher temperatures up to 194 degrees Fahrenheit and they require a lower flow past the motor due to the design.
Want to learn more about flow sleeves? Visit our YouTube Channel or give us a call!
Phone: 855.329.4519
