Prev Next

Power-Flo PF01011LC Submersible Dewatering Pump 0.75 HP 115V 1PH Manual 25' Cord

Price: $2,354.05
Quantity:
+ -
Usually ships within 3 weeks
SKU: PFPF01011LC


Shipping Weight:
55.0 LBS
Shipping Dimensions
Length: 10 In
Width: 17 In
Height: 11 In
WARNING Cancer and Reproductive Harm - www.P65Warnings.ca.gov

Power-Flo Submersible Dewatering Pump Description

These pumps are compact, lightweight powerful portable electric submersible pumps. They are whisper quiet and will perform in any position. Power-Flo pumps can be staged in series for higher head applications.

Power-Flo in-line design assures maximum heat transferred to the pumped liquid. Power-Flo pumps can operate in up to 140°F (60°C) temperature water. Power-Flo design provides the coolest operating motor for maximum life.

Power-Flo Submersible Dewatering Pump Typical Application

  • Dewatering

Power-Flo Submersible Dewatering Pump Features

  • DISHCARGE CASE: Aluminum, Hard Anodized
  • DIFFUSER: Aluminum, Hard Anodized
  • SUCTION CASE: Aluminum, Hard Anodized, with Wear Resistant Polyurethane Liner
  • FRAME & OUTER CASE: Aluminum, Hard Anodized
  • PUMP SHAFT: Stainless Steel
  • IMPELLER: Polyurethane
  • HARDWARE: Stainless Steel
  • O-RINGS: Buna-N
  • SEAL: Tandem Mechanical, Oil Lubricated
    • INBOARD: Carbon/Ceramic/Buna-N, Hardware-300 Series Stainless
    • OUTBOARD: Silicone Carbide/Silicone Carbide/Buna-N, Hardware-300 Series Stainless
  • STRAINER: Stainless Steel, 3/16" Holes
  • UPPER BEARING: Single Row, Shielded, Ball, Pre-Lubricated High-Temperature Grease, Load: Radial
  • LOWER BEARING: Single Row, Shielded, Ball, Pre-Lubricated High-Temperature Grease, Load: Radial & Thrust
  • CORD ENTRY: 25 ft., 14/4 SOOW, with Strain Relief and Pressure Grommet for Sealing
  • MOTOR: Class H Insulation, VPI
  • CONTROL: NEMA 3R Rainproof, 1 Phase-w/Start and Run Capacitors, 6 ft. Power Cord with 3 Prong Plug
  • WARRANTY: 1 Year

Power-Flo PF01011LC Specifications

  • VOLTAGE: 1ø, 115V, 60Hz
  • HORSEPOWER: 0.75 HP
  • AMP DRAW (full load): 11.0
  • MOTOR TYPE: Class H Insulation, VPI
  • RPM: 3450
  • MAXIMUM HEAD: 41'
  • MAXIMUM CAPACITY: 100 GPM
  • DISCHARGE PIPE SIZE: 2.0"
  • IMPELLER TYPE: Polyurethane
  • IMPELLER DIAMETER: 3.58"
  • CORD LENGTH: 25'
  • CORD SIZE: 14/4 SOOW, with Strain Relief and Pressure Grommet for Sealing
  • BODY CONSTRUCTION: Aluminum
  • MAXIMUM LIQUID TEMPERATURE: 140°F (60°C)
  • CONTROL BOX REQUIRED

Power-Flo Submersible Dewatering Pump Performance Curve

pf01000-1300-curve.jpg


WARNING Cancer and Reproductive Harm - www.P65Warnings.ca.govWARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov

Power-Flo Warranty

Sump/Effluent & Dewatering Pumps - 2 Years Limited Warranty

Manufacturer warrants, to the immediate purchaser and subsequent initial owner during the warranty period,every new pump to be free from defects in material and workmanship under normal use and service, when properly used and maintained, for a period of eighteen (18) months from date of manufacture or twelve (12) months from date of installation (which ever comes first). Failure due to wear due to excessive abrasives is not covered. The initial owner is the purchaser who first uses the pump after its initial installation, or for non-permanent installation,the first owner who uses the pump. The date of installation shall be determined by a dated sales receipt noting the model and serial number of the pump. The dated sales receipt must accompany the returned pump. Product will be repaired, replaced or re-manufactured at Manufacturer’s option. No allowance will be made for shipping charges,damages, labor or other charges that may occur due to product failure, repair or replacement. This warranty does not apply to and there shall be no warranty for any material or product that has been disassembled without prior approval of Manufacturer, subjected to misuse, misapplication, neglect, alteration, accident or act of God; that has not been installed, operated or maintained in accordance with Manufacturer’s installation instructions; that has been exposed to outside substances including but not limited to the following: sand, gravel, cement, mud, tar,hydrocarbons, hydrocarbon derivatives (oil, gasoline, solvents, etc.), or other abrasive or corrosive substances, wash towels or feminine sanitary products, etc. in all pumping applications. The warranty set out in the paragraph above is in lieu of all other warranties expressed or implied; and we do not authorize any representative or other person to assume for us any other liability in connection with our products. Contact Manufacturer at: 1-877-24PUMPS or www.powerfl opumps.com, Attention: Customer Service Department, to obtain any needed repair or replacement of part(s) or additional information pertaining to our warranty.MANUFACTURER EXPRESSLY DISCLAIMS LIABILITY FOR SPECIAL, CONSEQUENTIAL OR INCIDENTAL DAMAGES OR BREACH OF EXPRESSED OR IMPLIED WARRANTY; AND ANY IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE AND OF MERCHANTABILITY SHALL BE LIMITED TO THE DURATION OF THE EXPRESSED WARRANTY. Some states do not allow limitations on the duration of an implied warranty, so the above limitation may not apply to you. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

We've been helping customers since 1953

Trust Guard Security Scanned