Deming Vertical Sump Pump Product Description
Deming Column Sump Pumps are unmatched in quality, standardized design and construction to meet the demanding requirements of continuous pumping operation. Compare the many superior features of these pumps that contribute to long dependable service life.
Metallurgy in all irons, bronze fitted, all bronze, steel, stainless steel and other machinable alloys. Provision for handling liquids to 400ºF. Single pump or duplex unit with two single pumps mounted on common duplex sump cover.
Deming Vertical Sump Pump Typical Application
- Sump Drainage
- Flood Control
- Air Wash Systems
- Power Plants
- Industrial Processes
- Condensation Control
- Pollution Control
- Dewatering Service
- Process Plants
- Utility Service
Deming Vertical Sump Pump Features
- Always Primed: Submerged in Liquid Being Pumped.
- Compact: Minimum Floor Space Required.
- Leak-Proof: No Gland or Mechanical Seal in Liquid Contact.
- Low Installation Cost: Minimum Foundation and Piping Required.
- Versatile:
- Adjustable, Semi-Open Impeller to Maintain Performance.
- Above or Below Plate Discharge.
- Vented or Vapor-Tight Construction.
- Optional Guide Bearing Assemblies.
See Resources for Links to the Specifications and Pump Curves.
Call customer service for more details and pricing.
WARNING:
Cancer and Reproductive Harm - www.P65Warnings.ca.gov
Deming Vertical Sump Pump Product Resources
Download Deming Vertical Sump Pump Brochure
Download Deming Vertical Sump Pump Specifications - 4500 series
Download Deming Vertical Sump Pump Guide Bearing and Shaft Selection - 4500 Series
Download Deming Vertical Sump Pump Selection Data
Download Deming Vertical Sump Pump Assembly Fig. 4501, 4511 & 4521
Download Deming Vertical Sump Pump Dimensions Fig. 4501, 4511 & 4521 for Simplex Units
Download Deming Vertical Sump Pump Dimensions Fig. 4501, 4511 & 4521 for Duplex Units
Download Deming Vertical Sump Pump Dimensions 4560 Series Simplex Units
Download Deming Vertical Sump Pump Dimensions 4560 Duplex Units
Download Deming Vertical Sump Pump Selection Curves Fig. 4500, 3500RPM, 1750RPM, 1150RPM & 870RPM
Download Deming 4511 Series Vertical Sump Pump Curve Size 1-1/4S & 1-1/2S, 1150RPM
Download Deming 4511 Vertical Sump Pump Curve Sizes 1-1/2M & 2S,1150RPM
Download Deming 4511 Vertical Sump Pump Curve Size 1-1/2M, 1750 & 1150RPM
Download 4511 Vertical Sump Pump Curve Size 2M & 3S, 1150RPM
Download Deming 4511 & 4521 Vertical Sump Pump Curve Size 3MD & 1-1/2L, 1150RPM
Download Deming 4521 Vertical Sump Pump Curve Size 4MD & 5MD, 1150RPM
Download Deming 4521 Vertical Sump Pump Curve Size 5MSD & 6MD, 1150RPM
Download Deming 4521 Vertical Sump Pump Curve Size 6MLD, 1150RPM
Download Deming 4565, 4566 & 4568 Vertical Sump Pump Curve Sizes 4x4x12 DV & 6x4x12 DV 1150RPM
Download Deming 4565, 4566 & 4568 Vertical Sump Pump Curve Size 6x6x12 DV & 8x6x12 DV 1150RPM
Download 4565, 4566 & 4568 Vertical Sump Pump Curve Sizes 8x8x12 DV & 10x10x12 DV 1150RPM
Download Deming 4565, 4566 & 4568 Vertical Sump Pump Curve Size 10x10x12 DV, 1150RPM
Download Deming 4501 Vertical Sump Pump Curve Size 1"x1-1/2", 1750RPM
Download Deming 4501 & 4511 Vertical Sump Pump Curve Sizes 2-1/2" & 1-1/4S, 1750RPM
Download Deming 4511 Vertical Sump Pump Curve Sizes 1-1/2S & 1-1/2M, 1750RPM
Download Deming 4511 Vertical Sump Pump Curve Sizes 2S & 2M, 1750RPM
Download Deming 4511 Vertical Sump Pump Curve Sizes 3S & 3D, 1750RPM
Download Deming 4521 Vertical Sump Pump Curve Sizes 4MD & 5MD, 1750RPM
Download Deming 4511 & 4521 Vertical Sump Pump Curve Sizes 4S & 5MS, 1750RPM
Download Deming 4521 Vertical Sump Pump Curve Sizes 5MSD & 6MD, 1750RPM
Download Deming 4521 Vertical Sump Pump Curve Sizes 6MLD & 1-1/2L, 1750RPM
Download Deming 4565, 4566 & 4568 Vertical Sump Pump Curve Sizes 4x4x12 DV & 6x4x12 DV, 1750RPM
Download Deming 4565, 4566 & 4568 Vertical Sump Pump Curve Sizes 6x6x12 DV & 8x6x12 DV, 1750RPM
Download Deming 4565, 4566 & 4568 Vertical Sump Pump Curve Size 8x8x12 DV, 1750RPM
Download Deming 4511H Vertical Sump Pump Curve Sizes 1"x1-1/2", 3500RPM
Download Deming 4511H Vertical Sump Pump Curve Sizes 1-1/4 Sx1-1/2 S, 3500RPM
Download Deming 4511H Vertical Sump Pump Curve Sizes 2 Sx3 MD, 3500RPM
Limited 24 Month Warranty
Crane Pumps & Systems warrants that products of our manufacture will be free of defects in material and workmanship under normal use and service for twenty-four (24) months after manufacture date, when installed and maintained in accordance with our instructions. This warranty gives you specifi c legal rights, and there may also be other rights which vary from state to state. In the event the product is covered by the Federal Consumer Product Warranties Law (1) the duration of any implied warranties associated with the product by virtue of said law is limited to the same duration as stated herein, (2) this warranty is a LIMITED WARRANTY, and (3) no claims of any nature whatsoever shall be made against us, until the ultimate consumer, his successor, or assigns, notifi es us in writing of the defect, and delivers the product and/or defective part(s) freight prepaid to our factory or nearest authorized service station. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply. THE SOLE AND EXCLUSIVE REMEDY FOR BREACH OF ANY AND ALL WARRANTIES WITH RESPECT TO ANY PRODUCT SHALL BE TO REPLACE OR REPAIR AT OUR ELECTION, F.O.B. POINT OF MANUFACTURE OR AUTHORIZED REPAIR STATION, SUCH PRODUCTS AND/OR PARTS AS PROVEN DEFECTIVE. THERE SHALL BE NO FURTHER LIABILITY, WHETHER BASED ON WARRANTY, NEGLIGENCE OR OTHERWISE. Unless expressly stated otherwise, guarantees in the nature of performance specifi cations furnished in addition to the foregoing material and workmanship warranties on a product manufactured by us, if any, are subject to laboratory tests corrected for fi eld performance. Any additional guarantees, in the nature of performance specifi cations must be in writing and such writing must be signed by our authorized representative. Due to inaccuracies in field testing if a conflict arises between the results of field testing conducted by or for user, and laboratory tests corrected for field performance, the latter shall control. RECOMMENDATIONS FOR SPECIAL APPLICATIONS OR THOSE RESULTING FROM SYSTEMS ANALYSES AND EVALUATIONS WE CONDUCT WILL BE BASED ON OUR BEST AVAILABLE EXPERIENCE AND PUBLISHED INDUSTRY INFORMATION. SUCH RECOMMENDATIONS DO NOT CONSTITUTE A WARRANTY OF SATISFACTORY PERFORMANCE AND NO SUCH WARRANTY IS GIVEN. This warranty shall not apply when damage is caused by (a) improper installation, (b) improper voltage (c) lightning (d) excessive sand or other abrasive material (e) scale or corrosion build-up due to excessive chemical content. Any modification of the original equipment will also void the warranty. We will not be responsible for loss, damage or labor cost due to interruption of service caused by defective parts. Neither will we accept charges incurred by others without our prior written approval. This warranty is void if our inspection reveals the product was used in a manner inconsistent with normal industry practice and/or our specific recommendations. The purchaser is responsible for communication of all necessary information regarding the application and use of the product. UNDER NO CIRCUMSTANCES WILL WE BE RESPONSIBLE FOR ANY OTHER DIRECT OR CONSEQUENTIAL DAMAGES,INCLUDING BUT NOT LIMITED TO TRAVEL EXPENSES, RENTED EQUIPMENT, OUTSIDE CONTRACTOR FEES, UNAUTHORIZED REPAIR SHOP EXPENSES, LOST PROFITS, LOST INCOME, LABOR CHARGES, DELAYS IN PRODUCTION, IDLE PRODUCTION, WHICH DAMAGES ARE CAUSED BY ANY DEFECTS IN MATERIAL AND/OR WORKMANSHIP AND/OR DAMAGE OR DELAYS IN SHIPMENT. THIS WARRANTY IS EXPRESSLY IN LIEU OF ANY OTHER EXPRESS OR IMPLIED WARRANTY, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. No rights extended under this warranty shall be assigned to any other person, whether by operation of law or otherwise, without our prior written approval