Prev Next

Burks Condensate Return Systems 0.33 to 3.0 HP

Price: Call For Details
Quantity:
+ -
Usually ships within 2 weeks
SKU:


WARNING Cancer and Reproductive Harm - www.P65Warnings.ca.gov
burkslogo1.png

Burks Condensate Return Systems

Burks Condensate Units are designed for automatic return of hot water condensation from radiators, coils, ect. to low and high pressure boilers, or for return of water and other liquids to the overhead tanks of industrial gravity circulating systems. All units are shipped complete, ready for fast, easy installation.

Burks GV Series Condensate Return Systems Features

  • Pumps:
    • Vertically Flange-Mounted Centrifugal Pumps are of Bronze Fitted Construction with Mechanical Shaft Seal for Temperature to 200°F (93°C).
    • Seal Area is Automatically Vented and Flushed. Back Pull-Out Design Allows Servicing without Disturbing Piping.
    • Bronze Impellers are Precision Balanced for Smooth, Quiet Operation.
    • Efficient Hydraulic Design for Non-Overloading Performance at all Ratings Shown.
  • Receiver Tanks: Rugged Cast Iron Receivers for Lifetime Service Under the Most Sever Conditions. Low Return Inlet. Available in 9, 14, 20 and 36 Gallon Sizes.
  • Motors:
    • Drip-Proof NEMA Standard Motors have Dual Ball Bearings and Threaded Stainless Steel Shaft. All Single Phase Motors must be Installed with a Magnetic Starter which Provides Full Overload Protection. Failure to use Correct Starter and Overload Protectors will Void Warranty.
    • Single Phase Motors thru 2 HP are 115/230 Volt Only.
    • Three Phase Motors are 230/460 Volt, 60 Hz.
  • Controls:
    • Simplex Systems are Equipped with a Heavy Duty Adjustable Float Switch with Stainless Steel Float and Rod.
    • Duplex Systems are Equipped with a Mechanical Alternator.

Burks GV6 Series Condensate Return Systems Features

  • 1/3 thru 3 HP - Seven Stock Sizes.
  • Capacities to 80 GPM (5 L.P.S) - Heads to 130 Feet.
  • Efficient Hydraulic Design.
  • Enclosed Bronze Impeller Threaded onto Stainless Steel Motor Shaft.
  • Impeller Balanced for Smooth, Quiet Operation.
  • Replaceable Bronze Casing Wear Ring.
  • Back Pull-Out Design Allows Servicing without Disturbing Piping. Pump Casing Stays in Place.
  • Mechanical Shaft Seal is Self-Adjusting - for Temperatures to 225°F (107°C) and pressures to 150 PSI (1034kpa).
  • Special Seals Available for Higher Temperatures and Fluids other than Water.
  • Tappings Provided for Venting and Flushing Seal Area.
  • Bronze Fitted, Close Grain Cast Iron Construction is Standard. All Iron Available.
  • ODP Motors are Standard . Drip Cover Provided for Vertical Installation.
  • Every Pump is Factory Tested.

WARNING Cancer and Reproductive Harm - www.P65Warnings.ca.govWARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov

Limited 24 Month Warranty

Crane Pumps & Systems warrants that products of our manufacture will be free of defects in material and workmanship under normal use and service for twenty-four (24) months after manufacture date, when installed and maintained in accordance with our instructions. This warranty gives you specifi c legal rights, and there may also be other rights which vary from state to state. In the event the product is covered by the Federal Consumer Product Warranties Law (1) the duration of any implied warranties associated with the product by virtue of said law is limited to the same duration as stated herein, (2) this warranty is a LIMITED WARRANTY, and (3) no claims of any nature whatsoever shall be made against us, until the ultimate consumer, his successor, or assigns, notifi es us in writing of the defect, and delivers the product and/or defective part(s) freight prepaid to our factory or nearest authorized service station. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply. THE SOLE AND EXCLUSIVE REMEDY FOR BREACH OF ANY AND ALL WARRANTIES WITH RESPECT TO ANY PRODUCT SHALL BE TO REPLACE OR REPAIR AT OUR ELECTION, F.O.B. POINT OF MANUFACTURE OR AUTHORIZED REPAIR STATION, SUCH PRODUCTS AND/OR PARTS AS PROVEN DEFECTIVE. THERE SHALL BE NO FURTHER LIABILITY, WHETHER BASED ON WARRANTY, NEGLIGENCE OR OTHERWISE. Unless expressly stated otherwise, guarantees in the nature of performance specifi cations furnished in addition to the foregoing material and workmanship warranties on a product manufactured by us, if any, are subject to laboratory tests corrected for fi eld performance. Any additional guarantees, in the nature of performance specifi cations must be in writing and such writing must be signed by our authorized representative. Due to inaccuracies in field testing if a conflict arises between the results of field testing conducted by or for user, and laboratory tests corrected for field performance, the latter shall control. RECOMMENDATIONS FOR SPECIAL APPLICATIONS OR THOSE RESULTING FROM SYSTEMS ANALYSES AND EVALUATIONS WE CONDUCT WILL BE BASED ON OUR BEST AVAILABLE EXPERIENCE AND PUBLISHED INDUSTRY INFORMATION. SUCH RECOMMENDATIONS DO NOT CONSTITUTE A WARRANTY OF SATISFACTORY PERFORMANCE AND NO SUCH WARRANTY IS GIVEN. This warranty shall not apply when damage is caused by (a) improper installation, (b) improper voltage (c) lightning (d) excessive sand or other abrasive material (e) scale or corrosion build-up due to excessive chemical content. Any modification of the original equipment will also void the warranty. We will not be responsible for loss, damage or labor cost due to interruption of service caused by defective parts. Neither will we accept charges incurred by others without our prior written approval. This warranty is void if our inspection reveals the product was used in a manner inconsistent with normal industry practice and/or our specific recommendations. The purchaser is responsible for communication of all necessary information regarding the application and use of the product. UNDER NO CIRCUMSTANCES WILL WE BE RESPONSIBLE FOR ANY OTHER DIRECT OR CONSEQUENTIAL DAMAGES,INCLUDING BUT NOT LIMITED TO TRAVEL EXPENSES, RENTED EQUIPMENT, OUTSIDE CONTRACTOR FEES, UNAUTHORIZED REPAIR SHOP EXPENSES, LOST PROFITS, LOST INCOME, LABOR CHARGES, DELAYS IN PRODUCTION, IDLE PRODUCTION, WHICH DAMAGES ARE CAUSED BY ANY DEFECTS IN MATERIAL AND/OR WORKMANSHIP AND/OR DAMAGE OR DELAYS IN SHIPMENT. THIS WARRANTY IS EXPRESSLY IN LIEU OF ANY OTHER EXPRESS OR IMPLIED WARRANTY, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. No rights extended under this warranty shall be assigned to any other person, whether by operation of law or otherwise, without our prior written approval

We've been helping customers since 1953

Trust Guard Security Scanned