Prev Next

Barmesa BP50SGMSPDTPC Narrow Angle SPDT Pump Level Control W/Clamp 125/250V 50' Cord

Price: $105.00
Quantity:
+ -
Usually ships within 4 days
SKU: BMS32010251R


Shipping Weight:
4.6 LBS
Shipping Dimensions
Length: 6 In
Width: 10 In
Height: 10 In
WARNING Cancer and Reproductive Harm - www.P65Warnings.ca.gov

Barmesa BP-SGMSPDT Series Narrow Angle Pump Level Control

The Barmesa BP-SGMSPDT Series Narrow Angle Pump Level Control is Used to Accurately Monitor High (Normally Open) or Low (Normally Closed) Liquid Levels to Activate Pump Control Panels and Alarms in Water and Sewage Applications. It Features a Green Colored Cap for Easy Identification of SPDT Control Switch. This Switch can be Wired to Work in Either Normally Open or Normally Closed Applications.

Barmesa BP-SGMSPDT Series Narrow Angle Pump Level Control Features

  • Can be Wired to Work in Either Pump Down (Normally Open) or Pump Up (Normally Closed) Applications (Single Pole, Double Throw)
  • Mechanically-Activated, Snap Action Contacts.
  • High Impact, Corrosion Resistant, Polypropylene Float Housing
  • Not Sensitive to Turbulence.
  • Control Differential of 1.5 inches (4 cm) Above or Below Horizontal.
  • Green Colored Cap for Easy Identification of SPDT Control Switch.
  • Includes Standard Mounting Clamp and Boxed Packaging
  • 50' Control Switch with Clamp
  • UL & CSA Certified.
    OPTIONS
  • In Standard Cable Lengths of 15, 25 or 50 Feet (5, 8 or 15 meters).
  • Two Mounting Options for Flexibility in Installation: Mounting Clamp: for Applications Where the Float can be Attached to a Discharge Pipe or Similar Mounting Device and Externally Weighted, for Applications Where the Float can be Suspended From Above.

Barmesa BP-SGMSPDT Series Narrow Angle Pump Level Control Specifications

  • CABLE: Flexible 18 Gauge, 3 Conductor, SJOW, Water-Resistant CPE.
  • FLOAT: 2.74" Diameter x 4.83" Long (7.0 x 12.3 cm) High Impact, Corrosion Resistant, Polypropylene Housing for use in Sewage and Water up to 140 °F (60 °C).
  • MAXIMUM WATER DEPTH: 30 Feet (9 meters), 13 PSI (90 kPa).
  • ELECTRICAL: 5 Amp, 125/250 VAC, 60 Hz
  • NOTE: This Switch is not Recommended for Controlling: Electric Loads Less Than 100 Milliamps, 12 VAC and Non-Arcing Electric Loads.


WARNING Cancer and Reproductive Harm - www.P65Warnings.ca.govWARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov

Barmesa BP-SGMSPDT Series Narrow Angle Pump Level Control Product Resources

product-resourcesb.png

Barmesa BP-SGMSPDT Series Narrow Angle Pump Level Control Datasheet

BARMESA PUMPS FACTORY WARRANTY


Barmesa Pumps warrants that products of our manufacture will be free of defects in material and workmanship under normal use and service for 18 months from date of manufacture or 12 months from installation date whichever occurs first. This warranty gives you specific legal rights,which vary from state to state.

This warranty is a limited warranty, and no warranty related claims of any nature whatsoever shall be made against Barmesa Pumps, until the ultimate consumer or his/her successor notifies us inwriting of the defect and delivers the product and/or defective part(s) freight prepaid to our factory or nearest authorized service station as instructed by Barmesa Pumps. THERE SHALL BE NO FURTHER LIABILITY. WHETHER BASED ON WARRANTY. NEGLIGENCE OR OTHERWISE. PRODUCT SHALL BE EITHER REPLACED OR REPAIRED AT THE ELECTION OF BARMESA PUMPS. Guarantees relating to performance specifications provided in addition to the foregoing material and workmanship warranties on a product manufactured by Barmesa Pumps, if any, are subject to possible factory testing. Any additional guarantees, in the nature of certified performance specifications or time frame must be inwriting and such writing must be signed byour authorized factory manager at time of order placement and/or at time of quotation. Due to inaccuracies in field testing and should a conflict arises between the results of field testing conducted by or for the user, Barmesa Pumps reserves the right to have the product returned to our factory for additional testing.

This warranty shall not apply when damage is caused by (1) improper installation, (2) improper voltage, (3) lightning, (4) excessive sand or other abrasive material, (5) corrosion build-up due to excessive chemical content or (6) uncontrollable acts of god. Any modification of the original equipment will also void the warranty. We will not be responsible for loss, damage or labor cost due to interruption of service caused by defective pumps, parts or systems. Barmesa Pumps will not accept charges incurred by others without our prior written approval.

This warranty is void if our inspection reveals the product was used in a manner inconsistent with normal industry practice and/or our specific recommendations. The purchaser is responsible for communication of all necessary information regarding the application and use of the product. UNDER NO CIRCUMSTANCES WILL WE BE RESPONSIBLE FOR ANY OTHER DIRECT OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO TRAVEL EXPENSES, CONTRACTOR FEES, UNAUTHORIZED REPAIR SHOP EXPENSES, LOST PROFITS, LOST INCOME, LABOR CHARGES, DELAYS IN PRODUCTION, IDLE PRODUCTION, WHICH DAMAGES ARE CAUSED BY ANY DEFECTS IN MATERIAL AND/OR WORKMANSHIP AND/OR DAMAGE OR DELAYS IN SHIPMENT. THIS WARRANTY IS EXPRESSLY IN LIEU OF ANY OTHER EXPRESS OR IMPLIED WARRANTY. No rights extended under this warranty shall be assigned to any other person, whether by operation of law or otherwise, without our prior written approval.

IMPORTANT!

If you have a claim under the provision of the warranty, contact Barmesa Pumps or your authorized Barmesa Pumps Distributor:

warranty@barmesapumps.com

www.barmesapumps .com

We've been helping customers since 1953

Trust Guard Security Scanned