Hydromatic HVS200 Grinder Pump Description
The Hydromatic HV200 Series grinder is engineered from the ground up in order to overcome the increased debris and higher pressure required in today's wastewater environment. It features a patent-pending axial cutter design and semi-open impeller to effectively macerate challenging sewage solids into a fine slurry.
Hydromatic HVS200 Grinder Pump Features
- CABLE ENTRY SYSTEM:
- Cable Jacket Sealed by Compression Fitting; Individual Wires Sealed by Compression Grommet for Double Seal Protection against Water Ingress
- Replace Power Cord without Disturbing Motor for Ease of Maintenance
- OIL-FILLED MOTOR:
- Maximizes Heat Dissipation and Provides Constant Bearing Lubrication for Long Life
- High Torque Start/Run Capacitor for Single Phase Motors for Assured Starting Under Heavy Loads
- Internal Capacitors Eliminate Need for Control Panel
- HEAT SENSOR:
- Protects Motor from Burnout Due to Excessive Heat from any Overload Condition
- Automatically Resets when Motor has Cooled
- HEAVY 416 SST SHAFT: Corrosion Resistant, Reduces Shaft Deflection for Long Life
- LOWER DOUBLE ROW BALL BEARINGS: Absorb Both Axial and Radial Loads for Increased Durability
- DOUBLE MECHNICAL SHAFT SEALS: In Oil-Filled Seal Chamber for Continuous Lubrication, Superior Motor Protection
- SEAL LEAK PROBE:
- Located in Seal Chamber Instead of Motor Area for True Early Warning of Water Leaks. Allows Corrective Action Before Costly Motor or Bearing Failure Occurs.
- Activates Warning Light in Control Panel.
- SST SEMI-OPEN IMPELLER:
- Provides Improved Performance, Resists Clogging
- Pump-Out Vanes Help Keep Trash From Seal, Reduces Pressure at Seal Face for Longer Life
- AXIAL CUTTER SYSTEM:
- Constructed of 440 SST Hardened to 57-60Rc for Long Life.
- Easily Replaceable without Dismantling Pump.
- VOLUTE CASE: Cast Iron, 1-1/4" Vertical, Flanged Discharge.
Hydromatic HVS200M3-2-20 Specifications
- BODY CONSTRUCTION: Class 30 Cast Iron
- HORSEPOWER: 2.0 HP
- RPM: 3450
- MAXIMUM HEAD: up to 138'
- MAXIMUM CAPACITY: up to 31 GPM
- DISCHARGE PIPE SIZE: 1.25" (31.75 mm) Discharge
- CORD LENGTH: 20' Standard
- OPTIONAL CORD LENGTHS AVAILABLE
- CORD SIZE: 12-7; Type: SOOW
- AMP DRAW (full load): 9.0
- VOLTAGE: 3ø, 230V
- MAXIMUM LIQUID TEMPERATURE: 140°F
- MOTOR: Enclosed, Oil Cooled Induction
- IMPELLER CONSTRUCTION: Semi-Open 8 Vane, Stainless Steel
Hydromatic HVS200 Grinder Pump Curve
WARNING:
Cancer and Reproductive Harm - www.P65Warnings.ca.gov
STANDARD LIMITED WARRANTY
Pentair Hydromatic® warrants its products against defects in material and workmanship for a period of 12 months
from the date of shipment from Pentair Hydromatic or 18 months from the manufacturing date, whichever
occurs first – provided that such products are used in compliance with the requirements of the Pentair Hydromatic
catalog and technical manuals for use in pumping raw sewage, municipal wastewater or similar, abrasive-free,
noncorrosive liquids.
During the warranty period and subject to the conditions set forth, Pentair Hydromatic, at its discretion, will repair
or replace to the original user, the parts that prove defective in materials and workmanship. Pentair Hydromatic
reserves the right to change or improve its products or any portions thereof without being obligated to provide such
a change or improvement for prior sold and/or shipped units.
Start-up reports and electrical schematics may be required to support warranty claims. Submit at the time of start up
through the Pentair Hydromatic website: http://forms.pentairliterature.com/startupform/startupform.asp?type=h.
Warranty is effective only if Pentair Hydromatic authorized control panels are used. All seal fail and heat sensing
devices must be hooked up, functional and monitored or this warranty will be void. Pentair Hydromatic will cover
only the lower seal and labor thereof for all dual seal pumps. Under no circumstance will Pentair Hydromatic be
responsible for the cost of field labor, travel expenses, rented equipment, removal/reinstallation costs or freight
expenses to and from the factory or an authorized Pentair Hydromatic service facility.
This limited warranty will not apply: (a) to defects or malfunctions resulting from failure to properly install, operate or
maintain the unit in accordance with the printed instructions provided; (b) to failures resulting from abuse, accident
or negligence; (c) to normal maintenance services and parts used in connection with such service; (d) to units that
are not installed in accordance with applicable local codes, ordinances and good trade practices; (e) if the unit is
moved from its original installation location; (f) if unit is used for purposes other than for what it is designed and
manufactured; (g) to any unit that has been repaired or altered by anyone other than Pentair Hydromatic or an
authorized Pentair Hydromatic service provider; (h) to any unit that has been repaired using non factory specified/
OEM parts.
Warranty Exclusions: Pentair HYDROMATIC MAKES NO EXPRESS OR IMPLIED WARRANTIES THAT EXTEND
BEYOND THE DESCRIPTION ON THE FACE HEREOF. Pentair HYDROMATIC SPECIFICALLY DISCLAIMS THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR ANY PARTICULAR PURPOSE.
Liability Limitation: IN NO EVENT SHALL Pentair HYDROMATIC BE LIABLE OR RESPONSIBLE FOR
CONSEQUENTIAL, INCIDENTAL OR SPECIAL DAMAGES RESULTING FROM OR RELATED IN ANY MANNER TO
ANY Pentair HYDROMATIC PRODUCT OR PARTS THEREOF. PERSONAL INJURY AND/OR PROPERTY DAMAGE
MAY RESULT FROM IMPROPER INSTALLATION. Pentair HYDROMATIC DISCLAIMS ALL LIABILITY, INCLUDING
LIABILITY UNDER THIS WARRANTY, FOR IMPROPER INSTALLATION. Pentair HYDROMATIC RECOMMENDS
INSTALLATION BY PROFESSIONALS.
Some states do not permit some or all of the above warranty limitations or the exclusion or limitation of incidental or
consequential damages and therefore such limitations may not apply to you. No warranties or representations at any
time made by any representatives of Pentair Hydromatic shall vary or expand the provision hereof.