Hydromatic HPGF Submersible Sewage Grinder Pump Description
Hydromatic HPGF Submersible Sewage Grinder Pump is designed to meet the demands of Residential, Commercial and Resort Areas.
Hydromatic HPGF Typical Application
- Residential
- Commercial
- Resort Area
Hydromatic HPGF Superior Features
- One epoxy barrier and one compression fitting
for maximum protection against wicking and water
seepage into the motor housing.
- The heavy-duty ball bearings, upper (radial)
and lower (thrust), are continuously lubricated by
oil to ensure long service life.
- Electrical motor design combines the advantages of
high torque output with optimum running efficiency
engineered specifically for grinder operation.
- The stator is secured to the motor housing by means
of stator bolts and retaining ring which ensure ease of
maintenance if the need ever arises.
- Standard stainless steel shaft in grinder pump
- Dual seals for maximum moisture protection.
- Moisture detection probe.
- Exclusive “Dual Cutter” design cuts solids to smallest
particle size, thereby greatly reducing clogging, roping,
or binding.
- Engineered nonmetallic semiopen impeller molded to a bronze
insert for greatest torque driving capabilities. Impeller made of
high strength Valox® which provides highest level of corrosion
resistance and maximum toughness from impact for a wide
variety of slurry pumpage. Pump-out vanes preclude material
buildup around shaft and seal.
Hydromatic HPGF Key Features
- Explosion-proof
- Class 1, Division 1, Groups C & D
- Dual seals for maximum moisture protection
- Oil-filled motor for maximum heat dissipation and constant bearing lubrication
- Exclusive dual cutter design cuts solids to the smallest particle size
- Semi-open impeller provides steep non-overloading operating curve
- Available configurations, rails and accessories:
- Rail Systems Available
- Controls and Accessories Available
Hydromatic HPGF300M3-4 Technical Details
- BODY CONSTRUCTION: Class 30 Cast Iron
- HORSEPOWER: 3.0 HP
- RPM: 1750
- MAXIMUM HEAD: up to 113'
- MAXIMUM CAPACITY: up to 50 GPM
- DISCHARGE PIPE SIZE: 2" NPT Vertical Discharge
- CORD LENGTH: 35' Standard
- CORD SIZE: 14-4; Type: SOOW, W
- AMP DRAW (full load): 9.5
- VOLTAGE: 3ø, 230V
- MAXIMUM LIQUID TEMPERATURE: 140°F
- MOTOR: Enclosed, Oil Cooled Induction
- IMPELLER CONSTRUCTION: Semi-Open 5 Vane, Red Brass #85-5-5-5, ASTM B584-836
- IMPELLER SIZE: 8.0"
Hydromatic HPGF Pump Curve
WARNING:
Cancer and Reproductive Harm - www.P65Warnings.ca.gov
STANDARD LIMITED WARRANTY
Pentair Hydromatic® warrants its products against defects in material and workmanship for a period of 12 months
from the date of shipment from Pentair Hydromatic or 18 months from the manufacturing date, whichever
occurs first – provided that such products are used in compliance with the requirements of the Pentair Hydromatic
catalog and technical manuals for use in pumping raw sewage, municipal wastewater or similar, abrasive-free,
noncorrosive liquids.
During the warranty period and subject to the conditions set forth, Pentair Hydromatic, at its discretion, will repair
or replace to the original user, the parts that prove defective in materials and workmanship. Pentair Hydromatic
reserves the right to change or improve its products or any portions thereof without being obligated to provide such
a change or improvement for prior sold and/or shipped units.
Start-up reports and electrical schematics may be required to support warranty claims. Submit at the time of start up
through the Pentair Hydromatic website: http://forms.pentairliterature.com/startupform/startupform.asp?type=h.
Warranty is effective only if Pentair Hydromatic authorized control panels are used. All seal fail and heat sensing
devices must be hooked up, functional and monitored or this warranty will be void. Pentair Hydromatic will cover
only the lower seal and labor thereof for all dual seal pumps. Under no circumstance will Pentair Hydromatic be
responsible for the cost of field labor, travel expenses, rented equipment, removal/reinstallation costs or freight
expenses to and from the factory or an authorized Pentair Hydromatic service facility.
This limited warranty will not apply: (a) to defects or malfunctions resulting from failure to properly install, operate or
maintain the unit in accordance with the printed instructions provided; (b) to failures resulting from abuse, accident
or negligence; (c) to normal maintenance services and parts used in connection with such service; (d) to units that
are not installed in accordance with applicable local codes, ordinances and good trade practices; (e) if the unit is
moved from its original installation location; (f) if unit is used for purposes other than for what it is designed and
manufactured; (g) to any unit that has been repaired or altered by anyone other than Pentair Hydromatic or an
authorized Pentair Hydromatic service provider; (h) to any unit that has been repaired using non factory specified/
OEM parts.
Warranty Exclusions: Pentair HYDROMATIC MAKES NO EXPRESS OR IMPLIED WARRANTIES THAT EXTEND
BEYOND THE DESCRIPTION ON THE FACE HEREOF. Pentair HYDROMATIC SPECIFICALLY DISCLAIMS THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR ANY PARTICULAR PURPOSE.
Liability Limitation: IN NO EVENT SHALL Pentair HYDROMATIC BE LIABLE OR RESPONSIBLE FOR
CONSEQUENTIAL, INCIDENTAL OR SPECIAL DAMAGES RESULTING FROM OR RELATED IN ANY MANNER TO
ANY Pentair HYDROMATIC PRODUCT OR PARTS THEREOF. PERSONAL INJURY AND/OR PROPERTY DAMAGE
MAY RESULT FROM IMPROPER INSTALLATION. Pentair HYDROMATIC DISCLAIMS ALL LIABILITY, INCLUDING
LIABILITY UNDER THIS WARRANTY, FOR IMPROPER INSTALLATION. Pentair HYDROMATIC RECOMMENDS
INSTALLATION BY PROFESSIONALS.
Some states do not permit some or all of the above warranty limitations or the exclusion or limitation of incidental or
consequential damages and therefore such limitations may not apply to you. No warranties or representations at any
time made by any representatives of Pentair Hydromatic shall vary or expand the provision hereof.